 |
|
|
67 Electric Circuit Tester - Power On
| • |
Tests 6-12-21
volt cirsuits for wire breaks, shorts, fuse lamps,
relays, armatures, etc. with power on. |
| • |
4" inspection probe
set in threaded ferrel and screwed into plastic
handle. |
| • |
48" 16 gauge wire with
alligator clip. |
|
|
|
|
|
70 Heavy Duty Circuit Tester - Power On
| • |
Bulb lights within
handle to indicate open, grounded or short circuits
on 6-12-24 Volt AC or DC systems. |
| • |
Features heavy duty 4 3/4-in.
(121mm) probe and extra long 60-inch (152 cm)
cable to reach into any test area. |
| • |
Tension relief spring connects
cable to handle for long life. |
| • |
Heavy duty ground clip is
enclosed in thick anti-shock boot cover. |
|
|
|
|
|
571 Overhead valve Spring Compressor
| • |
Remove valve
spring without removing cylinder heads. |
| • |
Hex head on center screw
enables mechanic to use socket with ratchet wrench
or "T" handle. |
|
|
|
|
|
573 Delux Overhead Valve Spring Compressor
| • |
Removes valve springs on most cars
with overhead valves. |
| • |
Shorter overall length allows for access in confined
areas. |
| • |
Can be operated either by hand, 5/8-in. open end
wrench or 5/8-in. socket and ratchet. |
|
|
|
|
|
575 Universal Valve Lifter
| • |
For L-head and valve -inhead automotive,
truck tractor, bus and marine engines. |
| • |
Easily adjusted with a pin operated screw to valve
spring length. |
| • |
Powerful leverage with cam locking handle. |
|
|
|
|
|
189 Heavy Duty harmonic Balancer Puller
| • |
Designed to pull
harmonic balancers, vibration dampeners, pulleys,
and gears with tapped holes. |
| • |
Four slots in yoke allow
tool to be used in both two or three hole applications. |
| • |
Removeable, floating swivel
prevents damage to shaft ends. |
| • |
Zinc plated, yoke is forged
from alloy steel, heat treated. |
|
|
|
|
|
360 Engine Cylinder Hone, 2 - 7in.
| • |
For 2" to
7" diameter cylinder bores of cars, trucks,
tractors, buses, industrial engines, and small
air cooled engines. |
| • |
Adjustable to infinite diameters
throughout the range. |
| • |
Flexible shaft, controlled
spring action. |
| • |
Equipped with 4" medium
grit stones |
| • |
Operated by high or low speed
electric drills. Use with cutting oil for best
results. |
|
|
|
|
|
814 Strap Oil Filter Wrench
| • |
Adjusts quickly
to fit any spin on filter up to 6-in. diameter. |
| • |
Strong nylon web belt will
not slip. |
| • |
Use with 1/2-in. square drive
wrench. |
|
|
|
|
|
878 ratcheting Chain Wrench
| • |
Can be used on
any object shape from 5/8-in. to 5-in. in diameter. |
| • |
Use the chain with 1/2-in.
square drive. |
|
|
|
|
|
498 Flange Type Axle Puller
| • |
Can be used as
a regular wheel or hub puller as well as a flange
type puller. |
| • |
Bolt circle range from 4-1/2"
to 5-1/2" (114-140 mm) which covers all major
cars and small trucks with flange type axles. |
| • |
Four slots in the adapter
allow this tool to be used on either 4, 5, or
6 bolt design axles. |
| • |
Extra heavy 5-1/4 lb. slide
hammer with 5/8"-18 threads. |
|
|
|
|
|
29 SAE Clutch Aligning Tool
| • |
For reaching
and disconnecting the hydraulic clutch line from
the slave cylinder, without damage to the clutch
line or coupling. |
| • |
Fits Ford Hydraulic clutches
1988 to date. |
|
|
|
|
|
22 Shock Absorber Link & Tie Rod End Puller
| • |
Manufactured
from a single piece of drop forged, alloy, heat
treated steel. Zinc plated. |
| • |
Will stand up to hard use. |
| • |
16" long, 21/32"
jaw opening. |
|
|
|
|
|
194 Tie Rod End Puller & Pitman Arm Puller
| • |
For the safe
easy removal of pitman arm assebly from most cars
and light trucks. |
| • |
Forged, heat treated yoke
with extra heavy center screw. |
| • |
1 1/16-in. (27mm) opening,
1 3/4-in. (44mm) pull. |
|
|
|
|
|
512 Macpherson Strut Coil Spring Tool
| • |
Designed for
use on all vehicles equipped with MacPherson Struts. |
| • |
Allows you to quickly compress
the coil spring to replace shock absorber, spring
sets, repair bent strut or strut tube and repair
damaged spindle. |
| • |
Nut size 5/8-in. to 10. |
|
|
|
|
|
513 Master Macpherson Strut Tool
| • |
Designed for
use on all vehicles equipped with MacPherson struts. |
| • |
Allows you to quickly compress
the coil spring to replace shock absorber, spring
sets, repair bent strut or strut tube, and repair
damaged spindle. |
| • |
Features broad spring contact,
Acme threaded rod, and built-in detente pins to
help lock the coil in place. |
| • |
Professional kit, forged
construction for repetitive use. |
|
|
|
|
|
521 Snap Ring Plier
| • |
At the push of
a button, this heavy duty 2-in-1 tool converts
into an internal or external snap ring plier. |
| • |
External range: 1/4"
to 2" (7-48 mm). Internal range: 3/8"
to 2" (10-48 mm). 7-3/4" overall length
without tips. |
| • |
Includes five pairs of steel
alloy tips: Straight tips 0.36" (.9mm), .047"
(1.2mm), .070" (1.8mm). 90 degree bent tips:
0.36" (.9mm), 0.47" (1.2mm). |
|
|
|
|
|
651 Impact Wrench Kit
| • |
Great for handling
the really tough jobs. |
| • |
A short twist sets the working
cam and return spring. |
| • |
The anvil end is then struck
a sharp blow with a hammer. |
| • |
Loosens screws and bolts
even when rusted or wedged tight. |
| • |
3/8-in. Square Drive. |
| • |
Reversible action also tightens
screws and bolts. |
|
|
|
|
|
501 Bearing Splitter
| • |
For removing
generator gears, bearing cones, bearings, and
similar parts that ordinary puller jaws cannot
reach. |
| • |
Knife edges are flush on
one side for easy pulling. |
| • |
Bolts are heat treated for
added strength. |
| • |
Small Bearing Splitter |
| • |
Capacity: 0-in. to 2 1/4-in.
(57mm), 3/8-in. -16 holes |
|
|
|
|
|
503 Bearing Splitter
| • |
For removing
generator gears, bearing cones, bearings, and
similar parts that ordinary puller jaws cannot
reach. |
| • |
Knife edges are flush on
one side for easy pulling. |
| • |
Bolts are heat treated for
added strength. |
| • |
Bearing Splitter for use
with Puller No. 943. |
| • |
Capacity: 0-in. to 4 1/4-in.
(108mm), 5/8-in. -18 holes. |
|
|
|
|
|
